BMW X5 Owners & Service Manuals

BMW X5: Removing And Installing/Replacing Thermostat Cartridge (N62TU/N52K)

BMW X5 (G05) 2019-2025 Service & Repair Manual / Cooling System / Engine Radiator / Removing And Installing/Replacing Thermostat Cartridge (N62TU/N52K)

IMPORTANT: Danger of scalding! Only perform this work after engine has cooled down.

Necessary preliminary tasks:

Unlock and detach coolant hose (1).

Release nuts and remove thermostat cartridge (2).

Installation:

Engine Radiator
Fig. 20: Identifying Coolant Hose And Thermostat Cartridge

REMOVING AND INSTALLING/REPLACING MODULE CARRIER (N52K)

Necessary preliminary tasks:

Installation:

Bleed power steering unit.

Press lock (1) and remove holder (2) downwards.

Illustration shows the left holder: The same procedure applies to the opposite side.

Installation:

Rubber mounts fall out easily, ensure correct installation position.

Remove module carrier (1) towards bottom.

When replacing module carrier:

Convert power steering cooling loop.

Add final details to vehicle.

Check system for leaks.

REMOVING AND INSTALLING/REPLACING COOLANT EXPANSION TANK (N62TU/N52K)

IMPORTANT: Danger of scalding! Only perform this work after engine has cooled down.

Necessary preliminary tasks:

Unlock and detach coolant hose (1).

Release screws.

Raise coolant expansion tank (2) until plug for coolant level switch and lower coolant hose are accessible.

Installation:

Engine Radiator
Fig. 21: Identifying Coolant Hose And Expansion Tank

Unlock plug (1) and remove.

Unlock and detach lower coolant hose (2).

Remove expansion tank (3).

Engine Radiator
Fig. 22: Identifying Plug, Lower Coolant Hose, Expansion Tank

REMOVING AND INSTALLING/REPLACING POWER STEERING COOLING COIL (N62TU/N52K/M57T2)

Special tools required:

WARNING: Danger of scalding! Only perform this work after engine has cooled down.

IMPORTANT: When working on the oil, coolant or fuel circuit, you must protect the alternator against contamination.

Cover alternator with suitable materials.

Failure to comply with this procedure may result in an alternator malfunction.

Necessary preliminary tasks:

Press lines (1) in direction of cooling coil (2). Pull locking ring towards rear and keep pressed.

Detach lines (1) from cooling coil (2).

If necessary, use special tool 17 0 030 PLIERS.

IMPORTANT: Catch and dispose of emerging fluid.

Engine Radiator
Fig. 23: Identifying Lines And Cooling Coil

Release screws and detach side holder (1).

Tightening torque.

Feed out cooling coil (2) towards front and remove.

Engine Radiator
Fig. 24: Identifying Screws, Holder And Cooling Coil

READ NEXT:

 Oil Cooler

FLUSHING OIL COOLER WITH LINES (AUTOMATIC TRANSMISSION) Special tools required: 17 2 018 17 2 010 SET OF ADAPTERS 17 2 019 17 2 010 SET OF ADAPTERS NOTE: Carry out the work steps listed when: Fitt

 Oil Cooler Lines

REMOVING AND INSTALLING/REPLACING HEAT EXCHANGER FOR AUTOMATIC TRANSMISSION (N52K) ) IMPORTANT: Danger of scalding! Only perform this work after engine has cooled down. Necessary preliminary tasks:

 Cruise Control Systems

SEE MORE:

 Danger Of Poisoning If Oil Is Ingested/Absorbed Through The Skin

Danger of poisoning! Ingesting oil or absorbing through the skin may cause poisoning! Possible symptoms are: Headaches Dizziness Stomach aches Vomiting Diarrhoea Cramps/fits Unconsciousness Protective measures/rules of conduct: Pour oil only into appropriately marked containers Do not po

 Battery Vapor Separator

REPLACING BATTERY NEGATIVE LEAD WARNING: Observe safety instructions for handling vehicle battery. Follow instructions for disconnecting and connecting battery. IMPORTANT: Do not under any circumstances use force to pull/lever off Intelligent Battery Sensor (IBS). Necessary preliminary tasks:

© 2019-2025 Copyright www.bmwx5info.com