BMW X5 Owners & Service Manuals

BMW X5: Removing And Installing/Replacing Ski Bag On Rear Seat (Through-Loading System)

BMW X5 (G05) 2019-2023 Service & Repair Manual / Seats / Rear Seat, Through-Loading / Removing And Installing/Replacing Ski Bag On Rear Seat (Through-Loading System)

Special tools required:

Necessary preliminary tasks:

Release screws (1).

Tightening torque 52 26 09AZ.

Rear Seat, Through-loading
Fig. 146: Identifying Screws

Release screws (1).

Tightening torque 52 26 09AZ. Release screw (2).

Tightening torque 52 26 08AZ. Remove Top Tether eyelet.

Rear Seat, Through-loading
Fig. 147: Identifying Top Tether Eyelet Screw

Lever out rear ski bag frame (1) with special tool 00 9 317.

IMPORTANT: Risk of damage in marked area.

Plastic eyelet of front trim can break.

If necessary, replace faulty trim.

Rear Seat, Through-loading
Fig. 148: Identifying Special Tool (00 9 317)

Lever out pins.

Remove front ski bag trim (1) in direction of arrow.

Rear Seat, Through-loading
Fig. 149: Identifying Front Ski Bag Trim

REMOVING AND INSTALLING/REPLACING TRIM AND FRAME FOR SKI BAG

Special tools required:

Release screws (1).

Tightening torque 52 26 23AZ.

Lever out caps (1).

Release screws underneath.

Tightening torque 52 26 23AZ.

Tightening torque 52 26 23AZ. Release screw (1).

Tightening torque 52 26 21AZ. Remove Top Tether eyelet.

Lever out frame (1) for ski bag with special tool 00 9 317.

IMPORTANT: Risk of damage in marked area.

Plastic eyelet of front trim can break.

If necessary, replace faulty trim.

Remove front ski bag trim (1) in direction of arrow.

REMOVING AND INSTALLING/REPLACING TRIM FOR CENTRE ARMREST

Carefully unclip channel cover strip (1).

Installation:

Risk of damage! Plastic eyelets of front trim can break.

If necessary, replace defective trim or channel cover.

Unclip trim for centre armrest.

Installation:

If necessary, replace faulty clips.

READ NEXT:

 Replacing Cover On Backrest Side Section

Necessary preliminary tasks: Remove rest side section. Disengage cover in marked area from rest side section. Fig. 150: Identifying Cover Marked Area REMOVING AND INSTALLING/REPLACING LEFT OR RIGH

 Removing And Installing/Replacing Backrest Frame For Left Rear Seat (Through - Loading System)

Necessary preliminary tasks: Remove backrest cover. Remove retractor mechanism. Remove lock. Release screws (1). Installation: Replace screws and insert with Loctite. Tightening torque 52 26 07

 Replacing Seat Cover For Left & Right Rear

Special tools required: 52 0 050. Necessary preliminary tasks: Remove rear seat. Remove rear panel trim. Disengage welt in marked area from seat mechanism. Disengage welt in marked area from

SEE MORE:

 Removing And Installing Or Replacing Left Output Shaft

Special tools required: 31 4 170 Remove front wheel. IMPORTANT: Expand turning lock sufficiently to avoid damaging thread when releasing collar nut. Release collar nut (1), press brake pedal to floor for this purpose. Fig. 140: Identifying Collar Nut Remove left microfilter housing cover. IMPOR

 Front Axle + Steering: Wheel/Chassis Alignment Check Must Be Carried Out After The Following Work

Fig. 3: Identifying Front Axle Components A wheel/chassis alignment check must be carried out after the following work: Release of following screw/bolt connections: Steering gear to front axle carrier Lower control arm to front axle carrier Tie rod end to tie rod Replacement of followi

© 2019-2023 Copyright www.bmwx5info.com