BMW X5 Owners & Service Manuals

BMW X5: Removing And Installing/Replacing Servomotor For Left Eccentric Shaft (N62/N62TU)

BMW X5 (G05) 2019-2023 Service & Repair Manual / Engine / Engine (N62TU V8) / Variable Valve Gear / Removing And Installing/Replacing Servomotor For Left Eccentric Shaft (N62/N62TU)

REMOVING AND INSTALLING/REPLACING SERVOMOTOR FOR LEFT ECCENTRIC SHAFT (N62/N62TU)

IMPORTANT: Follow instructions issued by diagnosis tester.

Risk of damage to intermediate shaft.

(cylinder bank 5 to 8)

Necessary preliminary tasks:

IMPORTANT: Follow instructions issued by diagnosis tester.

Unlock plug (1) on servomotor (2) and disconnect.

Variable Valve Gear
Fig. 696: Identifying Plug On Servomotor

Unfasten screws.

Rotate servomotor (2) until no longer engaged in spline teeth of eccentric shaft.

Variable Valve Gear
Fig. 697: Rotating Servomotor

Installation:

Replace sealing ring on spacer.

Install servomotor (1) and screw in up to spacer.

Rotate servomotor (1) into correct installation position.

Install and tighten down screws.

Variable Valve Gear
Fig. 698: Rotating Servomotor Into Correct Installation Position

Installation:

Read out fault memory of control unit of Digital Motor Electronics (DME).

Check stored fault messages.

Rectify faults.

Now clear the fault memory.

REMOVING AND INSTALLING/REPLACING SERVOMOTOR FOR RIGHT ECCENTRIC SHAFT (N62/N62TU)

IMPORTANT: Follow instructions issued by diagnosis tester.

Risk of damage to intermediate shaft.

(cylinder bank 1 to 4)

Necessary preliminary tasks:

IMPORTANT: Follow instructions issued by diagnosis tester.

Unlock plug (1) on servomotor (2) and disconnect.

Variable Valve Gear
Fig. 699: Identifying Plug On Servomotor

Unfasten screws.

Rotate servomotor (2) until no longer engaged in spline teeth of eccentric shaft.

Variable Valve Gear
Fig. 700: Rotating Servomotor

Installation:

Replace sealing ring on spacer.

Install servomotor (1) and screw in up to spacer.

Rotate servomotor (1) into correct installation position.

Install and tighten down screws.

Variable Valve Gear
Fig. 701: Identifying Sealing Ring

Installation:

Read out fault memory of control unit of Digital Motor Electronics (DME).

Check stored fault messages.

Rectify faults.

Now clear the fault memory.

REMOVING AND INSTALLING/REPLACING LEFT ECCENTRIC SHAFT SENSOR (N62/N62TU)

(cylinder bank 5 to 8)

Necessary preliminary tasks:

Unfasten screws.

Remove eccentric shaft sensor (1).

Variable Valve Gear
Fig. 702: Locating Eccentric Shaft Sensor Screw

Installation:

Read out fault memory of control unit of Digital Motor Electronics (DME).

Check stored fault messages.

Rectify faults.

Now clear the fault memory.

REMOVING AND INSTALLING/REPLACING RIGHT ECCENTRIC SHAFT SENSOR (N62/N62TU)

(cylinder bank 1 to 4)

Necessary preliminary tasks:

Unfasten screws.

Remove eccentric shaft sensor (1).

Variable Valve Gear
Fig. 703: Locating Eccentric Shaft Sensor Screw

Installation:

Read out fault memory of control unit of Digital Motor Electronics (DME).

Check stored fault messages.

Rectify faults.

Now clear the fault memory.

REPLACING CONTROL UNIT (VALVETRONIC)

Switch off ignition.

Disconnect battery leads.

CAUTION: Follow instructions for removing and installing electronic control units.

Observe following instructions before replacing control unit: Program control unit.

Remove right fresh air duct.

Release screw and remove holder (1).

Release screws and remove cover (2) from control unit box.

NOTE: Release screws on seal (3) only when removing wiring harness.

Variable Valve Gear
Fig. 704: Locating Holder, Screws And Cover

Installation:

Insert tabs (1) in openings (2) and close cover.

Variable Valve Gear
Fig. 705: Locating Tabs And Cover

Unlock and detach plug connections on Valvetronic control unit (1).

Remove Valvetronic control unit (1).

Variable Valve Gear
Fig. 706: Identifying Valvetronic Control Unit

NOTE: Interrogate fault memory of DME control unit.

Check stored fault messages.

Rectify faults.

Then clear fault memory.

READ NEXT:

 Oil Supply

CHECKING ENGINE OIL PRESSURE Special tools required: 11 4 050 13 3 061 13 3 063 13 6 051 13 6 054 NOTE: To check the engine oil pressure, the oil pressure switch must be removed and the specia

 Oil Pump With Filter

REMOVING AND INSTALLING/REPLACING OIL PUMP (N62) Necessary preliminary tasks: Drain engine oil. Remove upper oil sump section. Remove reinforcement plate. Unscrew nut (1). Tightening torque 11

 Oil Filling, Dipstick

REMOVING AND INSTALLING/SEALING GUIDE TUBE FOR OIL DIPSTICK (N62) Necessary preliminary tasks: Remove intake air manifold. Drain engine oil. NOTE: For purposes of clarity, this work step is shown

SEE MORE:

 Repairing Airbag Cables

IMPORTANT: Only repair those cables which show visible signs of damage. In the event of visible damage, make sure there is only one cable repair in effect after the repair work. If no visible damage can be identified, the entire cable must be replaced. When carrying out repairs to the airbag wiring

 Enlarging the cargo area

Principle The cargo area can be enlarged by folding down the rear seat backrests. General information The rear seat backrest of the second seat row is divided at a ratio of 40-20-40. The side rear seat backrests and the center section can be folded down separately. The rear seat backrests can be fo

© 2019-2023 Copyright www.bmwx5info.com