BMW X5: Bluetooth connection
Functional requirements
- Compatible device with Bluetooth interface.
Compatible devices.
- The vehicle key or BMW display key is in the
vehicle.
- The device is ready for operation.
- Bluetooth is switched on in the vehicle and
on the device.
- The pairing readiness is displayed on the
Control Display.
- Bluetooth presettings, such as visibility, may
be required on the device; refer to the operating
instructions of the device.
Activate Bluetooth
1. "COM".
2. "Mobile devices".
3. Tilt the Controller to the right.
4. "Settings".
5. "Bluetooth".
6. Select setting.
Connecting the device
1. "COM".
2. "Mobile devices".
3. Tilt the Controller to the right.
4. "New device".
5. "Phone calls and audio".
The vehicle's Bluetooth name is displayed on
the Control Display.
6. Compare the control number displayed on
the Control Display with the control number
on the display of the mobile device, and confirm
that the two match.
7. A Bluetooth connection is established.
The mobile device is connected to the vehicle
and displayed in the device list.
Frequently Asked Questions
All requirements are met and all required steps
were completed in the specified order. Despite
that, the mobile device does not function as expected.
In this case, the following explanations can help:
Why could the mobile phone not be paired or
connected?
- There are too many Bluetooth devices connected
to the mobile phone or vehicle.
In the vehicle, delete Bluetooth connections
with other devices.
Delete the Bluetooth connection from the device
list on the mobile phone and start a new
device search.
Too many Bluetooth devices with the same
function are paired.
- The mobile phone is in power-save mode or
has only a limited remaining battery life.
Charge the mobile phone and deactivate the
power-save mode where required.
Why does the mobile phone no longer react?
Why can telephone functions not be used via
iDrive?
Why are no or not all telephone book entries displayed
or why are they incomplete?
- Transmission of the telephone book entries is
not yet complete.
- It is possible that only the telephone book entries
of the mobile phone or the SIM card are
transmitted.
- It may not be possible to display telephone
book entries with special characters.
- It may not be possible to transmit contacts
from social networks.
- The number of phone book entries to be
transmitted is too high.
- Data volume of the contact too large, for instance
due to stored information such as
memos.
Reduce the data volume of the contact.
- A mobile phone can only be connected as
audio source or as telephone.
Configure the mobile phone and connect it
with the telephone function.
- Contact was created in the contact list of the
phone after the last synchronization.
Synchronize contacts again: "Reload
contacts".
How can the telephone connection quality be
improved?
- Adjust the strength of the Bluetooth signal on
the mobile phone, depending on the mobile
phone.
- Insert the mobile phone into the wireless
charging tray.
- Adjust the volume of the microphone separately
in the sound settings.
If all points in this list have been checked and the
required function is still not available, contact
Customer Relations, a dealer's service center or
another qualified service center or repair shop.
READ NEXT:
General information
For certain applications, such as apps, the data
exchange between smartphone and vehicle occurs
via WLAN.
Functional requirements
Standby state is switched on.
Compatible device
General information
Screen Mirroring enables mirroring (outputting)
of the smartphone display on the Control Display.
Functional requirements
Compatible smartphone with Screen Mirroring
interface.
Principle
Android Auto allows the operation of certain
functions of a compatible smartphone via voice
control and iDrive.
General information
The range of services offered depends on the
country.
Func
SEE MORE:
1. Opening spot-weld bonds
Set punch mark in center of weld spot. Set 8 mm dia. weld spot drill bit
on punch mark and drill
through top metal sheet.
Or open weld spot with Vario Drill spot welding cutter (refer to WORKSHOP
EQUIPMENT &
PLANNING CD, Chapter 7).
NOTE: Because the weld spo
REMOVING AND INSTALLING OR REPLACING BATTERY POSITIVE LEAD
(BETWEEN STARTER, ALTERNATOR AND BATTERY POSITIVE TERMINAL)
Necessary preliminary tasks:
Read out fault memory of DME control unit; if necessary, work through
test schedules.
Switch off ignition.
Disconnect battery negative lead.
Rem