BMW X5 Owners & Service Manuals

BMW X5: Setting the speed - Active Cruise Control with Stop&Go function ACC

BMW X5 (G05) 2019-2022 Owners Manual / Controls / Driver assistance systems / Setting the speed - Active Cruise Control with Stop&Go function ACC

Setting the speed

Maintaining and storing the speed

Driver assistance systems

Press the rocker switch up or down once while the system is interrupted. The system will be activated.

The current speed is maintained and stored as desired speed.

The stored speed is displayed on the speedometer.

DSC Dynamic Stability Control is switched on, if necessary.

The speed can also be stored by pressing a button.

Press the button.

Changing the speed

Driver assistance systems

Press the rocker switch up or down repeatedly until the desired speed is set.

If active, the displayed speed is stored and the vehicle reaches the stored speed when the road is clear.

Hold the rocker switch in position to repeat the action.

Adjusting the distance

Safety information

Warning

The system cannot serve as a substitute for the driver's personal judgment. Due to the system limits, deceleration can be late. There may be a risk of accident or risk of damage to property.

Be aware to the traffic situation at all times. Adjust the distance to the traffic and weather conditions and maintain the prescribed safety distance, possibly by braking.

Reduce distance

Press the button repeatedly until the desired distance is set.

Instrument cluster will display selected distance.

Increase the distance

Press the button repeatedly until the desired distance is set.

Instrument cluster will display selected distance.

Automatic adaptation of the distance

Depending on the equipment and national-market version: the system can be adjusted so that the distance to the vehicle driving in front is automatically adjusted within the configured distance according to the traffic situation or the ambient conditions, for instance poor visibility.

1. "CAR".

2. "Settings".

3. "Driver Assistance".

4. If necessary, "Driving".

5. "Speed Limit Assistance".

6. "Adjust distance acc. to situation".

Continuing cruise control

An interrupted cruise control can be continued by calling up the stored speed.

Make sure that the difference between current speed and stored speed is not too large before calling up the stored speed. Otherwise, unintentional deceleration or acceleration may occur.

Press the button on the steering wheel with the system interrupted:

With steering and traffic jam assistant.

Without steering and traffic jam assistant.

Cruise control is continued with the stored values.

In the following cases, the stored speed value is deleted and cannot be called up again:

Changing between cruise control with/without distance control

Safety information

Warning

The system does not react to traffic driving ahead of you, but instead maintains the stored speed. There may be a risk of accident or risk of damage to property. Adjust the set speed to the traffic conditions and brake as needed.

Change over mode of the cruise control

Switching cruise control without distance control off and on:

With steering and traffic jam assistant: switch on distance control:

Press the button.

Without steering and traffic jam assistant: switch on distance control:

After changing, a Check Control message is displayed.

READ NEXT:

 Displays in the instrument cluster - Active Cruise Control with Stop&Go function ACC

Displays in the instrument cluster General information Depending on the equipment version, the displays in the instrument cluster may vary. Display in the speedometer Depending on the equipment, a mar

 System limits - Active Cruise Control with Stop&Go function ACC

System limits System limits of the sensors Additional information: Cameras Radar sensors Detection range The detection capability of the system and the automatic braking performance are limited.

 Speed Limit Assistant

Principle Speed Limit Assistant supports driving at the speed limit. A suggested speed can be applied. General information When the systems in the vehicle, e.g., Speed Limit Info, detect a change of t

SEE MORE:

 Removing And Installing/Replacing Oil Pump (N52K)

Necessary preliminary tasks: Remove oil sump Release screws (1). Tightening torque: 11 41 1AZ. Installation: Replace aluminium screws. Remove intake pipe (2) in direction of arrow. Installation: Replace sealing ring. NOTE: To release bolt (1), insert a 6 mm drill bit between sprocket wheel and

 Cardboard Box

Minimum set: Measuring and testing equipment Note: As storage location "Y3" for MINI V-adapter leads (with launch of R56) SI number: 2 09 06 313 Order number: 00 0 110 Cardboard box Fig. 13: Identifying Cardboard Box (00 0 110) CARDBOARD BOX (SET) FOR CABLE CABINET Note: For storing adapter cables

© 2019-2022 Copyright www.bmwx5info.com