BMW X5: Removing And Installing/Replacing Centre Console For 3Rd Seat Row
Release screws (1).
Remove centre console (1) towards top.
Installation:
Feed centre console (1) with guides into trim (2).
Version with rear cabin fan only:
Unclip ventilation grille (1).
Unclip operating unit (1).
Set down operating unit (1) in downward direction in centre console.
Lift centre console (1) on left and right over air outlet. Remove centre console (1) towards top.
Installation:
Feed centre console (1) with guides into trim (2).
REMOVING AND INSTALLING GAP COVER FOR FLOOR PANEL ON LEFT OR RIGHT
Necessary preliminary tasks:
- Remove luggage compartment floor panel
Release screws (1).
Remove gap cover (2).
REMOVING AND INSTALLING FRONT TRIM FOR 3RD SEAT ROW ON LEFT OR RIGHT
Release screws (1).
Remove trim (2).
REMOVING AND INSTALLING/REPLACING LEFT SEAT BACKREST FRAME
Necessary preliminary tasks:
- Remove 3rd seat row.
- Remove backrest cover.
- Removing actuating mechanism for rear seat backrest.
- Remove outer trim.
Detach Starlock washer (1) from shaft.
Remove shaft.
Installation:
Detach Starlock washer (1) from shaft. Remove shaft. Installation: Fit left and right plastic sleeves on shaft.
Release fitting screws (1).
Tightening torque: 52 30 02AZ.
Release outer bearing screw (1).
Tightening torque: 52 30 03AZ.
Remove seat backrest frame (2) from assembly frame.
Replacement only:
- Removing seat fabric.
REMOVING AND INSTALLING/REPLACING RIGHT SEAT BACKREST FRAME
Operation is identical to:
- Removing right seat backrest frame.
REMOVING AND INSTALLING/REPLACING REAR PANEL ON LEFT OR RIGHT REAR SEAT BACKREST
Necessary preliminary tasks:
- Remove trim for release unit.
NOTE: The right side is removed in the same way as the left side.
Unclip rear panel from backrest frame.
Installation:
Replace faulty clips.
Insert rear panel with guide at bottom into backrest.
REPLACING BOWDEN CABLE FOR LEFT OR RIGHT REAR SEAT BACKREST
Necessary preliminary tasks:
- Disengage Bowden cable nipple from actuating unit.
Unclip Bowden cable (1) from backrest frame.
Unhook Bowden cable nipple (2).
Feed out Bowden cable from backrest frame.
REMOVING AND INSTALLING/REPLACING ACTUATING MECHANISM FOR REAR SEAT BACKREST
Necessary preliminary tasks:
- Remove backrest cover.
Unclip trim (1) and feed out from release lever (2).
Installation:
Retaining lugs must not be damaged.
If necessary, replace faulty trim (1).
Press in detent lugs and remove release unit (1).
Disengage Bowden cable sleeve (1) from actuating unit (2).
Carefully press retaining lug (1) back with screwdriver and feed Bowden cable nipple (2) out of actuating unit.
REMOVING AND INSTALLING OR REPLACING LEFT OR RIGHT REAR HEAD RESTRAINT
Move head restraint (1) upwards to maximum extent.
Press lock (2) and pull out head restraint.
READ NEXT:
Removing And Installing/Replacing Seat Cover For Left Or Right Rear Seat
Special tools required:
52 0 050
Necessary preliminary tasks:
Remove front trim.
Open tension cable (1).
Disengage welt (2) from seat frame.
Disengage tensioning cable over wire eyelets.
Remo
Special Tool
SPECIAL TOOL BOARD I
Order number: 00 0 010
Special tool board I
SPECIAL TOOL BOARD II COMPLETE
In conjunction with: 00 0 230 This board can be used in a min. 4 m long
moving special tool cabinet.
No
SEE MORE:
General Information On Intelligent Battery Sensor (IBS)
WARNING: Danger of destruction in event of mechanical strain
Do not introduce any additional connections at the battery
negative
terminal.
Do not modify the grounding cable.
The grounding cable also serves to dissipate heat.
Do not establish any connection between the IBS and the sensor
scr
Replacing Front Crankshaft Radial Seal (N52K)
Special tools required:
11 9 221
11 9 222
11 9 223
11 9 224
11 9 231
11 9 232
11 9 233
Necessary preliminary tasks:
Remove vibration damper
IMPORTANT: Do not release central bolt.
If the central bolt is released, the sprocket wheels of the timing chain and the
oil pump will no longer be
