BMW X5 Owners & Service Manuals

BMW X5: Removing And Installing/Replacing Left Intermediate Levers (N62 From 9/03 And N62TU)

BMW X5 (G05) 2019-2024 Service & Repair Manual / Engine / Engine (N62TU V8) / Camshaft / Removing And Installing/Replacing Left Intermediate Levers (N62 From 9/03 And N62TU)

Special tools required:

(cylinder bank 5 to 8)

Removal of intermediate levers is described separately from installation.

Necessary preliminary tasks:

IMPORTANT: The inlet camshaft must first be rotated so that when the bearing bracket is removed the intermediate levers do not slip out and damage the camshaft.

Rotate inlet camshaft against direction of rotation until lettering (1) on 8th cylinder points upwards in cylinder axis and cam is horizontal.

Camshaft
Fig. 401: Locating Camshaft Numbers

IMPORTANT: Camshaft bearing caps of cylinders 1 to 4 and 5 to 8 must not be mixed up.

NOTE: Bearing caps of inlet camshaft are marked on cylinder bank 5 to 8 with R E1 to R E5 from inlet side.

Release nuts and remove bearing cap R E1.

Camshaft
Fig. 402: Locating Camshaft Bearing Caps Nut

Release 8 nuts of bearing bracket (1) from outside to inside.

Camshaft
Fig. 403: Locating Nuts Of Bearing Bracket

NOTE: Rocker arms are freely accessible after bearing bracket has been removed.

Do "not" remove rocker arm (1) on inlet side.

IMPORTANT: Rocker arms (1) are divided into individual tolerance classes.

The tolerance classes are designated as illustrated with the numbers from 1 to 4.

Used rocker arms (1) may only be reused in the same position.

When replacing rocker arms (1) on inlet side: install rocker arms of the same tolerance class in the same position.

Camshaft
Fig. 404: Locating Rocker Arms On Inlet Side

Clamp special tool 11 9 470 as illustrated in a vice.

Camshaft
Fig. 405: Identifying Special Tool (11 9 470)

IMPORTANT: Do not tilt bearing bracket (1).

Carefully lift out bearing bracket (1).

Camshaft
Fig. 406: Identifying Bearing Bracket

Place bearing bracket (1) with inlet camshaft and eccentric shaft as illustrated on special tool 11 9 470.

Secure bearing bracket (1) with a nut (special tool 11 9 473).

Camshaft
Fig. 407: Identifying Special Tool (11 9 470) And (11 9 473)

IMPORTANT: The lower section of the bearing bracket (1) is machined with the cylinder head and must not be mixed up.

NOTE: Lower section of bearing bracket (1) remains on cylinder head.

Camshaft
Fig. 408: Identifying Lower Section Of Bearing Bracket On Cylinder Head

NOTE: The mounting of the bearing bracket described later can only be carried out if the inlet camshaft has not been axially displaced.

Special tools 11 9 472 and 11 9 475 prevent the inlet camshaft from rotating and moving while the intermediate levers are installed.

Fit special tool 11 9 472 and secure with special tool 11 9 475.

Camshaft
Fig. 409: Identifying Special Tool (11 9 480) And (11 9 490)

Insert special tool 11 9 474 and initially tighten without play.

Camshaft
Fig. 410: Identifying Special Tool (11 9 474)

NOTE: Removal of intermediate levers is described on 8th cylinder.

The same procedure is applicable to cylinders 5 to 7.

Raise one end of torsion spring (1) with special tool 11 9 480.

Lift out intermediate lever (2) and set down in an orderly fashion.

IMPORTANT: Keep holding torsion spring (1) with special tool 11 9 480.

Camshaft
Fig. 411: Identifying Torsion Spring, Intermediate Lever With Special Tool (11 9 480)

Attach special tool 11 9 490 to end of torsion spring.

Support end of torsion spring protected with special tool 11 9 490 on inlet camshaft.

Camshaft
Fig. 412: Identifying Special Tool (11 9 480) And (11 9 490)

IMPORTANT: Intermediate levers (2) are divided into individual tolerance classes.

Only intermediate levers of the same tolerance class may be fitted in a single cylinder head.

The tolerance classes are designated as illustrated with the numbers from 1 to 5.

Used intermediate levers (2) may only be reused in the same position.

Camshaft
Fig. 413: Locating Intermediate Levers

Raise second end of torsion spring (1) with special tool 11 9 480.

Lift out intermediate lever (2) and set down in an orderly fashion.

IMPORTANT: Keep holding torsion spring (1) with special tool 11 9 480.

Camshaft
Fig. 414: Identifying Torsion Spring With Special Tool (11 9 480)

Attach special tool 11 9 490 to second end of torsion spring.

Support end of torsion spring protected with special tool 11 9 490 on inlet camshaft.

Camshaft
Fig. 415: Identifying Special Tool (11 9 480) And (11 9 490)

Installation:

Installation of intermediate levers is described separately from removal.

Clean all bearings and cams of inlet camshaft and lubricate with engine oil.

IMPORTANT: Intermediate levers (2) are divided into individual tolerance classes.

Only intermediate levers of the same tolerance class may be fitted in a single cylinder head.

The tolerance classes are designated as illustrated with the numbers from 1 to 5.

Used intermediate levers (2) may only be reused in the same position.

Lubricate all sliding surfaces on intermediate lever (2) with engine oil.

Camshaft
Fig. 416: Locating Intermediate Levers

Raise torsion spring (1) with special tool 11 9 480.

Remove special tool 11 9 490.

Camshaft
Fig. 417: Identifying Special Tool (11 9 480) And (11 9 490)

Hold torsion spring (1) with special tool 11 9 480.

Install intermediate lever (2) from above.

Insert end of torsion spring (1) into guide on intermediate lever (2).

Camshaft
Fig. 418: Identifying Torsion Spring With Special Tool (11 9 480)

Raise second end of torsion spring with special tool 11 9 480.

Remove special tool 11 9 490.

Camshaft
Fig. 419: Identifying Special Tool (11 9 480) And (11 9 490)

Hold torsion spring (1) with special tool 11 9 480.

Install intermediate lever (2) from above.

Insert end of torsion spring (1) into guide on intermediate lever (2).

Camshaft
Fig. 420: Identifying Torsion Spring, Intermediate Lever With Special Tool (11 9 480)

Remove special tool 11 9 474.

Camshaft
Fig. 421: Identifying Special Tool (11 9 474)

Remove special tools 11 9 472 and special tools 11 9 475.

Camshaft
Fig. 422: Identifying Special Tool (11 9 480) And (11 9 490)

Ends of compression rings (1) point upwards.

Make sure compression rings (1) are engaged at ends.

Camshaft
Fig. 423: Locating Compression Rings

IMPORTANT: Rocker arms (1) slip slightly when bearing bracket is fitted.

Make sure rocker arms (1) are secured as illustrated on hydraulic valve clearance compensating elements and on valves.

Align rockers (1) straight.

Camshaft
Fig. 424: Identifying Rocker Arms

Remove special tool 11 9 473.

Remove bearing bracket (1) from special tool 11 9 470.

Camshaft
Fig. 425: Identifying Special Tool (11 9 470) And (11 9 473)

IMPORTANT: Do not tilt bearing bracket (1).

Lower bearing bracket (1) from above and carefully bring into contact with cylinder head.

Insert nuts and tighten by hand without play.

IMPORTANT: Make sure none of the intermediate levers or rocker arms have slipped out.

Tighten down nuts from inside to outside.

Tightening torque 11 31 1AZ.

Camshaft
Fig. 426: Locating Nuts Of Bearing Bracket

IMPORTANT: Camshaft bearing caps of cylinders 1 to 4 and 5 to 8 must not be mixed up.

Fit bearing cap R E1 in such a way that marking is legible from inlet side.

Install nuts and tighten down.

Tightening torque 11 31 1AZ.

Camshaft
Fig. 427: Locating Camshaft Bearing Caps Nut

Rotate inlet camshaft in direction of rotation until cam on 5th cylinder points upwards at an angle as shown in illustration.

NOTE: The marking (1) on the hexagon drive of the inlet camshaft faces upwards.

Camshaft
Fig. 428: Locating Marking On Hexagon Drive Of Inlet Camshaft Faces Upwards

Install inlet and exhaust adjustment unit on left side.

Install spark plugs on cylinder bank 5 to 8.

Install left cylinder head cover.

Install ignition coils on cylinder bank 5 to 8.

Install servomotor for left eccentric shaft.

Assemble engine.

READ NEXT:

 Removing And Installing/Replacing Right Intermediate Levers (N62 From 9/03 And N62TU)

Special tools required: 11 9 470 11 9 472 11 9 473 11 9 474 11 9 475 11 9 480 11 9 490 (cylinder bank 1 to 4) Removal of intermediate levers is described separately from installation. Necessa

 Rocker Arm With Bearing

 Removing And Installing/Replacing Rocker Arms On Left Inlet Side (N62 From 9/03 And N62TU)

Special tools required: 11 9 470 11 9 473 (cylinder bank 5 to 8) Removal of rocker arms is described separately from installation. Necessary preliminary tasks: Remove servomotor for left eccentr

SEE MORE:

 Integrated key

General information The driver's door can be locked and unlocked without the vehicle key using the integrated key. Depending on the national-market version, the integrated key also fits the glove compartment. Safety information Warning For some country versions, unlocking from the inside is only po

 Driving Dynamics Control

Principle The Driving Dynamics Control influences the driving dynamics properties of the vehicle. The vehicle can be adjusted depending on the situation using various driving modes. General information The following systems are affected, for instance: Engine characteristics. Steptronic transmiss

© 2019-2024 Copyright www.bmwx5info.com