BMW X5: Park Distance Control
REMOVING AND INSTALLING (REPLACING) CONTROL UNIT (PARK DISTANCE CONTROL)
IMPORTANT: Read and comply with notes on protection against electrostatic damage (ESD protection).
Necessary preliminary tasks:
- Remove flap in luggage compartment panel on right.
Fold insulating mat (1) to one side.
.png)
Fig. 1: Identifying Insulating Mat
Disconnect plug connection (1).
Remove control unit (2).
.png)
Fig. 2: Identifying Control Unit And Plug Connection
Replacement:
Carry out programming/coding.
REMOVING AND INSTALLING/REPLACING A FRONT ULTRASONIC TRANSDUCER (CENTRE)
Necessary preliminary tasks:
- Remove front bumper trim.
Disconnect plug connection (1) and unclip ultrasonic transducer from retaining lugs (2).
Installation:
Retaining lugs (2) must not be damaged! Make sure ultrasonic transducer is securely seated.
.png)
Fig. 3: Identifying Retaining Lugs And Plug Connection
REMOVING AND INSTALLING/REPLACING A FRONT ULTRASONIC TRANSDUCER (SIDE)
Necessary preliminary tasks:
- Remove front bumper trim 51 11 FRONT BUMPER
Disconnect plug connection (1) and remove rubber grommet (2).
Installation:
Make sure rubber grommet (2) is securely seated.
.png)
Fig. 4: Identifying Rubber Grommet And Plug Connection
Unlock retaining tabs (1) in direction of arrow and pull ultrasonic transducer (2) out of holder.
.png)
Fig. 5: Unlocking Retaining Tabs And Ultrasonic Transducer
Installation:
Make sure rubber ring (1) is correctly seated on ultrasonic transducer (2).
.png)
Fig. 6: Identifying Rubber Ring
REMOVING AND INSTALLING/REPLACING A REAR ULTRASONIC TRANSDUCER (PARK DISTANCE CONTROL)
Necessary preliminary tasks:
- Remove rear bumper trim 51 12 REAR BUMPER
Disconnect plug connection (1) and remove rubber grommet (2).
Installation:
Make sure rubber grommet (2) is securely seated.
.png)
Fig. 7: Identifying Rubber Grommet And Plug Connection
Unlock retaining tabs (1) in direction of arrow and pull ultrasonic transducer (2) out of holder.
.png)
Fig. 8: Unlocking Retaining Tabs And Ultrasonic Transducer
Installation:
Make sure rubber ring (1) is correctly seated on ultrasonic transducer (2).
.png)
Fig. 9: Identifying Rubber Ring
READ NEXT:
Reversing Camera
INSTRUCTIONS FOR ADAPTING ADJUSTMENT UNIT FOR REVERSING CAMERA
(CORGHI KDS QUICK - ACTION CLAMP)
NOTE: The operation is described for the left-hand side; proceed in the
same way for the right-hand si
Night Vision
CALIBRATING REVERSING CAMERA
WARNING: Danger of injury!
Laser radiation at adjustment unit.
Do not look into the beam!
Laser class 2
As per EN 60825-1: 1994
P< or = 1 mW
Lambda = 632.8 nm
NOTE: Ca
SEE MORE:
Removing And Installing/Replacing Left Or Right Push Rod/Integral
Link
NOTE: If the integral link is detached from the wheel carrier or
swinging arm, it is
necessary after reinstallation to carry out a wheel/chassis alignment check.
Necessary preliminary tasks:
Remove rear wheel.
Tension coil spring (and leave on vehicle).
Version with ride-height control: Deacti
Pressing Output Shaft Out Of Drive Flange (Wheel Hub) And Drawing In
Special tools required:
33 2 111
33 2 115
33 2 116
33 2 117
33 2 118
33 2 160
33 2 201
33 2 202
33 2 203
33 2 205
33 2 207
33 2 208
33 5 070
WARNING: Risk of injury!
It is not permitted to use the impact screwdriver to press out and draw in
the output shaft.
IMPORTANT: Risk of damage!
