BMW X5 Owners & Service Manuals

BMW X5: Cable Cabinet, Complete

CABLE CABINET II, COMPLETE

Note: For extended accommodation of adapter leads as well as measuring and test equipment

SI number: 0 02 99 (399)

Order number: 00 0 180

Cable cabinet II, complete

Consisting of:

1 = 00 0 182 Film set II

Note: For identifying storage locations in cable cabinet II - Currently applicable status

2 = 00 0 183 Cable holder set - H -

Note: For cable cabinet II only 16 guide rails each with 15 straps for holding adapter cables - Currently applicable status

3 = 00 0 184 CD holder

Note: For holding two program CDs with sleeve - Can be fitted in cable cabinets I and II

4 = 00 0 186 Drawer block

Note: For cable cabinet II only

5 = 00 0 187 Holder set for test adapters

Note: For cable cabinet II only

6 = 00 0 188 Strap set (optional)

Note: 20 straps for cable holders - H - For expanding suspended cables in cable cabinets I and II

Maintenance & General Information
Fig. 23: Identifying Cable Cabinet II (00 0 180)

CABLE CABINET I, COMPLETE

Note: With set of films and accessories - For storing adapter cables as well as measuring devices and testers

SI number: 0 02 99 (399)

Order number: 00 0 190

Cable cabinet I, complete

Consisting of:

1 = 00 0 191 Cable cabinet

Note: Without contents or accessories Basis for cable cabinets I and II

2 = 00 0 192 Set of films I

Note: For identifying storage locations in cable cabinet I - valid status in each case

3 = 00 0 193 Cable holder set - H -

Note: For cable cabinet I only 24 guide rails each with 15 retaining straps for accommodating adapter leads

4 = 00 0 194 Cable carrier - B -

Note: For accommodating engine test leads For extending cable suspensions in cable cabinets I and II

6 = 00 0 195 Swivel board frame

Note: Carrier of cable suspensions in cable cabinets I and II

7 = 00 0 196 Drawer block

Note: For cable cabinet I only

8 = 00 0 197 Magnet with roller

Note: For improved location and spacing of swivel boards - For retrofitting in cable cabinets I and II only

9 = 00 0 198 Compartment floor

Note: For cable cabinet I only

10 = 00 0 199 Index

Note: For finding BMW special tools for automotive electrics in cable cabinets I and II

Maintenance & General Information
Fig. 24: Identifying Cable Cabinet I (00 0 190)

READ NEXT:

 Cross Member

Minimum set: Mechanical tools Note: To hold the engine when removing and installing the front axle support, the oil sump and the transmission Engine: M10, M20, M20B25, M20B27, M21, M30, M30B34, M30Tu

 Shelf

Note: With mounting material. SI number: 0 01 00 (549) Order number: 00 0 250 Shelf Fig. 29: Identifying Shelf (00 0 250) DRAWER BLOCK Note: With 5 lockable drawers SI number: 0 01 00 (549) Order num

 Hook Set

HOOK SET, COMPLETE, FOR 00 1 300, USA VERSION Order number: 00 1 340 Hook set, complete, for 00 1 300, USA version Consisting of: 1 = 00 1 341 Hook set for film no. 1 USA-Version 2 = 00 1 342 Hook set

SEE MORE:

 Replacing Output Flange On Transfer Box At Rear (ATC 700)

IMPORTANT: After completing work, check gear oil level, see Replenishing /Changing Transfer Case Oil (ATC 700) and top up if necessary. Use only the approved gear oil in this transfer box. NOTE: Operations for removing output flange are identical to replacing radial shaft seal. Installatio

 Vehicle care

Vehicle care products General information BMW recommends using vehicle care and cleaning products from BMW. Suitable vehicle care products are available from a dealer's service center or another qualified service center or repair shop. Safety information Warning Cleansers can contain substances that

© 2019-2026 Copyright www.bmwx5info.com